January

Winter Door Wreath With Pinecones and a Soft Ribbon

Make a winter door wreath from an existing evergreen base, with a pinecone cluster, an off-center ribbon and practical fastening and hanging steps.

The Christmas bow is off the wreath, but the evergreen base still looks good against the door. A winter door wreath can keep that greenery working with a different arrangement of pinecones and ribbon. This version uses one cluster at the lower side, leaving most of the wreath's shape visible.

Greenery, Three Pinecones and Ribbon

Start with a sound artificial evergreen wreath about eighteen to twenty-four inches across. You'll also need three medium pinecones, florist wire, wire cutters and a length of ribbon suitable for your doorway. Choose a wreath and materials intended for the conditions where they'll hang.

The ribbon can be soft blue, brown gingham or plain cream. Hold it against the door before cutting; a shade that looks strong on the table may disappear from the walkway. Use a length that gives you a full bow and two tails, then trim the tails after hanging.

Inspect the base before adding anything. Look for loose branches, broken wire or a hanger that needs replacing. Repair only as the wreath's construction allows, and don't use a damaged base that won't hold its shape.

Work on a covered table with the cutters and wire away from children and pets. Have a small dish ready for wire offcuts so they don't disappear among the branches.

Shape the Greenery Before Adding the Cluster

Set the wreath upright against a wall and find its most natural top. Fluff the artificial branches outward and slightly forward, following the shape of the base. Open the center enough that the ring looks round rather than like a solid mound.

Choose the lower-left or lower-right side for the pinecones. Try both by placing the cones loosely on the table beside the wreath. Follow the sweep of the branches when choosing a side.

Spread the branches in the chosen area so the cones will sit against the structure, not on a springy cushion of tips. Keep some greenery in front and some behind. That gives the cluster a place in the wreath instead of making it look attached to the outermost edge.

Try the largest cone at the outside edge, then closer to the center. The first position makes a wider silhouette; the second makes a fuller cluster. Choose the one that follows the greenery most naturally.

Wire Three Pinecones Into a Loose Triangle

Place the largest cone closest to the outside edge of the wreath, with the two smaller ones beside it. Let their tips point in slightly different directions. A loose triangle gives the group shape without looking like three cones in a straight row.

Wrap florist wire around the lower part of the first cone, tucking it between the scales where it can grip securely. Leave two ends long enough to reach the wreath's structural frame. Test the hold gently before fastening the cone to the base.

Pass those ends through the greenery and around the frame, then twist them together at the back. Trim excess wire and bend the cut ends inward so they can't scratch the door or catch fingers. Repeat for the other two cones, checking the arrangement from the front each time.

If a cone is too brittle to wire securely, choose another. Avoid relying on a loose cone wedged between branches, especially on a door that opens and closes often. Give the finished cluster a gentle movement test over the table before hanging it.

Tie the Bow Beside the Cones

Make the bow separately so you can adjust its loops without disturbing the cluster. Form two loops, cross and tie them, then pull gently until the center holds. Lay the bow beside the pinecones and decide whether you prefer the tails pointing down or following the wreath's curve.

Fasten the bow to the frame with a separate piece of wire or the ribbon's own ties if they are suitable. Hide the fastening behind the bow's center. Keep the loops clear of the cone tips so the ribbon's shape can be seen.

For a softer look, leave the loops a little unequal. For a neater look, match their length and trim the tails at an angle. Neither needs extra ornaments around the rest of the wreath.

Hang the wreath briefly before making the final cuts. The tails may appear much longer against the door than they did on the table.

Hang It Where the Door Can Work

Use a hanger rated for the wreath's weight, door surface and outdoor conditions. Follow its installation instructions, then check that the door closes normally with it in place.

Open the door fully and watch the ribbon. Shorten or reposition anything that catches near the latch, handle or frame. Check the back of the wreath for exposed wire before letting it rest against the door.

From the walkway, the evergreen circle should read first and the pinecones second. If the bow hides the whole cluster, move it a little outward. If the cones disappear, bring one of the three forward.

A nearby winter garden flag can repeat the quiet outdoor welcome. Our Peace Begins Here evergreen flag is one option beside the path, where its printed greenery can relate to the wreath without crowding the door.

The greenery and pinecones can stay through the rest of winter. When you want a small change, tie on a different ribbon.

Evergreen wreath with exactly three pinecones clustered above a cream bow on a weathered blue cottage door.
A Year of Celebrations free printable collection

A free gift

Never miss a day worth celebrating

Get the whole year of holidays and birthdays in five printable pages, plus a coloring page, free in your inbox.